Browse all practice questions for the Texas Flame Operator Certification Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Texas Flame Operator Certification Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • Excess fuel that has been removed shall be stored in accordance with which standards?
  • True or False: The fuel supply and auxiliary services necessary to the operation of the flame effect control system (compressed air supply, oxidizers, additives, etc.) shall be permitted to be turned on prior to the activation of control power.
  • Which features must be present on each prepackaged single-use container receiver?
  • During Site Inspection, what area does the operator inspect?
  • What is the minimum control requirement for Flame Group VII?
  • What is the primary requirement for the fire performance area?
  • True or False: The AHJ can require a walk-through and a representative demonstration of the flame effects before approval.
  • What best describes a Flame Effect System?
  • Which of the following is NOT a safety feature required for Group II through Group VII control systems?
  • Which description matches Group III Flame Effect?
  • Where is the accumulator charge valve installed?
  • Evidence of insurance is not required at permit application?
  • Which flame groups have both automatic flame verification and automatic fuel controls?
  • Hybrid Flame Effect is defined as
  • Who bears the overall responsibility for flame effect operations and safety?
  • Smoking and other ignition sources shall be prohibited within what distance of the fueling area?
  • What is a Flame Effect Burner?
  • True or False: The arming of the effect shall be manually or automatically monitored and confirmed until the effect is fired.
  • What must chain grips be made of?
  • Which outdoor activity is explicitly exempt from these regulations?
  • Which general safety measures should be observed for flame effect systems and portable flame effects?
  • Which NFPA 160 personnel is explicitly listed as Spotter/Fire Watch?
  • How should temperatures be taken during testing?
  • Which description defines Group V Flame Effect?
  • Which statement describes Flame Group I Type Effect?
  • Which precaution should a Fire Performer take with excess fuel, residue, fuel-soaked waste etc.?
  • Which statement best describes Flame Group II Type Effect?
  • What must spotters always carry?
  • How must prepackaged single-use containers be disposed of?
  • What action should be taken with fuel residue after the performance?
  • True or False: Smoking can be permitted by performers as a part of a performance with a flame effect.
  • Which element is required to be included in the Flame Effect Site Plan?
  • Which description matches the Flame Effect System?
  • True or False: When control functions are required, an effect valve is not needed.
  • What provision is required to remove unused liquid fuel from the system?
  • What must standby personnel be able to do in case of an alarm?
  • Which site plan component relates to storage and holding areas?
  • For Flame Group V, which statement about the interface between the flame effect control system and the main show control is correct?
  • What does SDS stand for?
  • Which flame effect appliance uses fuel from a prepackaged single-use container?
  • When is testing and evaluation documentation for a flame effect provided?
  • Define 'open flame' as used in the regulations.
  • True or False: Once a device is armed it only needs to be confirmed once as long as it has not been fired.
  • Why must accumulators conform to standards such as the ASME code, DOT regulations, or PED?
  • Venues should have what for areas both visible to and out of sight of the technical director, where a person might be exposed to injury during firing?
  • How should a Hazard Area surrounding a Flame Effect be monitored?
  • Before transporting a portable flame effect, which safety actions must be performed?
  • Flame effects testing: true or false?
  • What must the Flame Effect Operator advise all performers and support personnel of?
  • What does the term Rated refer to?
  • Which Flame Groups have automatic flame verification as a feature?
  • Where should the operating power for firing any flame effect originate?
  • Who is required to wear protective clothing?
  • Where is the automatic fuel shutoff valve (effect valve) located?
  • Which term refers to a circuit or mechanism that, when actuated, results in the complete shutdown and extinguishment of all flame effects controlled by it?
  • What is required to move a fuel-soaked wick through an audience for a fire performer?
  • What is the maximum allowed temperature rise for combustible materials above ambient after equilibrium is reached?
  • Flame effect systems shall be maintained to design specifications. True or False?
  • An operator can demonstrate competency by experience and training or by holding a license acceptable to the AHJ.
  • What must be performed prior to installation with prepackaged single-use containers?
  • When external pressure sources are used with flame effect appliances, what design requirement must be provided?
  • Which flame group can only be permanent installation?
  • Which statement best describes a Flame Effect Plan?
  • Personal computers and single-board controllers can be used in related applications such as display, logging, and trending of process variables. Which of the following statements is true?
  • When is a pressure supervisory control system required in order to prevent operation of a liquid-fuel flame appliance?
  • Flame effects shall only be fired after they have been confirmed as armed following the completion of the enable and arming process and confirmation that the hazard area is clear.
  • For temporarily installed flame effects, what must a use permit specify?
  • What post-performance procedure applies to fire props?
  • What is the definition of a Solid-Fuel Flame Effect Appliance?
  • Which description defines Group II Flame Effect?
  • Can prepackaged single-use containers be refilled?
  • What should the flame effect valve do on loss of the hold-open signal?
  • Paint, starting fluid, air fresheners, lubricants, hairsprays, and insecticides are prohibited for use as flame effect fuels.
  • Which statement correctly defines Permanent Installation in terms of permit duration?
  • How must accumulators be designed, manufactured, certified and tested?
  • How long is a Pyrotechnic or Flame Operator's license valid before renewal is required?
  • Minimum control requirements for Flame Group IV Flame Effect include which items?
  • Who is required to specify a minimum and maximum ambient temperature rating for flame effect appliances when it is critical to proper operation?
  • Which statement regarding varying timing of the flame effect is correct?
  • What condition should the premises where flame effect devices are installed and fired be kept in?
  • True or False: There must be an unobstructed path from the fueling area to the performance area.
  • When should an accumulator be charged?
  • Which method encourages the operator to monitor the area by requiring them to look toward the flame when enabling?
  • Name an Example of a Flame Group IV Type Effect.
  • What must be done before transporting Liquid-Fuel?
  • What are spotters/firewatch in charge of?
  • Gaseous Fuel is defined as?
  • Which Flame Groups have proximate cast as a feature?
  • According to an infrared surface thermometer, what is the maximum exposed skin temperature for audience members?
  • The Flame Effect System Classification and General Requirements do not apply to which type of person?
  • When does the enable process begin?
  • Which Flame Groups have automatic fuel controls as a feature?
  • True or False: Emergency operations shall be in accordance with the plan approved by the AHJ.
  • Name an Example of a Flame Group III Type Effect.
  • Can a Flame Operator fire an effect that uses a pyrotechnic ignitor?
  • What is a Flame Effect Operator inspecting as part of their Site Inspection?
  • Which group should review the Flame Effect Plan to ensure coordinated emergency response?
  • Which entity has the authority to approve performer smoking in a flame effects performance?
  • Can a municipality or county enact an ordinance or order prohibiting or further regulating flame effects or pyrotechnics beyond these standards?
  • For a hybrid flame effect, which NFPA standards apply to the respective portions?
  • Which entity approves the emergency operations plan?
  • True or False: Liability insurance policy must be issued by an insurer authorized to do business in Texas and countersigned by a licensed Texas insurance agent.
  • Accessible Hazard Area is defined as
  • What must flame effect control systems be designed and installed to do?
  • What is the location of the effect valve relative to the burner?
  • The Fire term refers to the sequence of control system functions that result in the deliberate release of fuel for ignition.
  • Which scenario would be included in Flame Group III Type Effect?
  • For permanently installed flame effects, what must the use permit specify?
  • What kind of offense is a violation of the Texas Occupational Code under 2154.253 Use of Flame Effects or Pyrotechnics?
  • How is the minimum tank size for liquefied flammable gas flame effects determined?
  • Name an Example of a Flame Group III Type Effect
  • Fire Watch is best described as the assignment of a person or persons to an area for the express purpose of
  • Which groups are, or can be, automatically controlled?
  • Which term describes an installation lasting longer than 180 days?
  • NFPA 1126 standard covers what?
  • Which statement best describes the minimum control requirements for Flame Group III?
  • If a Hazard Area is not actively monitored by a person (or PME), what two alternatives are acceptable?
  • When other safety-critical effects, allied equipment, and other proximate equipment can produce contributory hazards, what should the effect safety controller have?
  • Is it permissible to handle flame effect materials or devices while under the influence of alcohol, narcotics, or judgment-impairing drugs?
  • LNG stands for which fuel?
  • Which term describes a pilot flame supervised by a primary safety control?
  • How often should fire props be tested to verify operation?
  • What role does a fire watch play in interrupting during flame effects operation?
  • Which Flame Group's controls are designed by the designer and acceptable to AHJ?
  • Non-effect safety controllers should not be used to allow, trigger, or request safety-critical action unless signals of these non-effect safety controllers are intercepted and qualified by an effect safety controller that has responsibility for allowing safety-critical actions.
  • Which statement defines Temporary Installation?
  • In flame safety, which event triggers a Safety Shutdown (Lockout)?
  • Which option correctly defines Group III Flame Effect?
  • Fueling stations for Fire Performers must be attended by who whenever a hazard is present?
  • What device ensures a shutoff is automatic for each flame effect?
  • If the state fire marshal proposes to suspend, revoke, or refuse to renew a license or permit, the hearing is conducted by which agency?
  • Which NFPA 160 personnel is NOT listed?
  • Which statement about fueling area safety is true?
  • Which description correctly defines a Prepackaged Single-Use Container Valve?
  • Which statement about use permits is true?
  • Which statement accurately reflects whether fire protection and life safety systems can be completely interrupted during the operation of flame effects?
  • Which scenario would be a Flame Group II Type Effect?
  • What term describes maintaining the premises in neat and orderly condition?
  • A Fire Hazards Evaluation may be required under which circumstance?
  • When should the plan be reviewed with the AHJ, Flame Effect Operator(s), and the Building Owner or Representative?
  • Spill containment shall be used during refilling of containers as approved by the AHJ.
  • Which item is included in the Flame Effect Plan Content as to the production location?
  • Which statement is true about AHJ involvement in flame effects approvals?
  • Group IV Flame Effects can be installed only as permanent installations. Which option reflects this?
  • Who provides documentation for testing flame effects?
  • The Flame Effect System should be made of which material?
  • Prior to removing a portable flame effect from one venue and transporting it to another, which steps must be followed?
  • Liquid-Fuel Flame Effect Appliance uses what as primary fuel?
  • Mixing what with fuel while inside an accumulator is prohibited?
  • Which of the following is a requirement for fuels delivered through a central distribution system?
  • Which scenario would be included in Flame Group IV Type Effect?
  • Which term describes an attended, manually controlled flame effect?
  • Why are flame effects tested?
  • When portable flame effects are not in use, how should they be stored?
  • Control systems must be inoperable unless a Flame Operator intentionally does two actions: 1. Deliberately applies control power. 2. Enables or Arms the control system.
  • Which of the following is a required characteristic of an emergency stop in automatically controlled flame effects?
  • Refillable containers shall be refilled and pressurized in a location approved by the AHJ.
  • When flame effects are used inside a building, what must the building have or provide acceptable to the authority having jurisdiction?
  • Which groups are included in the Fire Hazard Evaluation coordination?
  • Compared to a public display permit, the minimum liability insurance for a flame or pyrotechnic effect permit is:
  • Flame Effect Safety Controller?
  • When piping is used, what pressure should the system be tested at?
  • The volume of fuel stored in an accumulator tank shall be no more than what is required to produce the desired flame effect.
  • Group II Flame Effects can be installed outdoors only. Which option correctly reflects this restriction?
  • Documentation of Flame Effects Devices and Materials should be available onsite to whom?
  • Solid-Fuel Flame Effect Appliance uses primary fuel?
  • Spill containment during refilling of containers is required when approved by which entity?
  • What defines a Flame Effect Appliance?
  • Who must first approve of smoking by performers as part of a performance with a flame effect?
  • If the operator, technical director, or assistant does not have continuous sight of the enable process or hazard area, what arrangement is permitted with approval?
  • Where must the manual shutoff valve be installed for central distribution fuels?
  • Documentation for testing flame effects should come from whom?
  • The failure of a device, component, system, or mechanism that results in an immediately dangerous situation is described as?
  • Which statement best defines a valve in the flame effect system?
  • Name an Example of a Flame Group VII Type Effect.
  • Which flame groups have both attended and automatic fuel controls?
  • If not all safety concerns can be seen by one operator, how many enable buttons are required?
  • When should fire and life safety systems that have been interrupted be restored?
  • Which option best defines a Performer?
  • What feature should PME pushbuttons provide to confirm the enable signal has been sent?
  • What area must be observed by the operator throughout the entire period the flame effect is enabled and fired?
  • Which event must occur before the enable process continues?
  • Which document is used to convey information to the AHJ for evaluating a flame effect for permit application?
  • What is the recommended stance on spotters' visibility of hazards?
  • NFPA 160 Standard Covers What?
  • For Flame Group VI, what additional requirement applies when cast members are in close proximity to the flame effect?
  • For Groups II through VII, which mechanism is required to prevent accidental firing?
  • Fuel-soaked waste disposal should follow which guidance?
  • Which valve is located between the two safety shutoff valves?
  • Who is responsible for the emergency pre-show announcement?
  • Control systems are designed to prevent harm to humans, animals or equipment.
  • Which two flame groups do not contain permanent installation as a feature?
  • What topics should be included in additional training for spotters/firewatch?
  • Which documents should be available on site and accompany the flame effects equipment?
  • Firing by methods other than the opening of a manual or electrically actuated fuel release valve may be acceptable.
  • True or False: The operator of any flame effect shall understand and be familiar with the operating manual or instructions.
  • Gaseous-Fuel Flame Effect Appliance uses what as primary fuel?
  • Who must approve all flame effects?
  • Which of the following best describes the scope of a Site Inspection for flame effects?
  • Minimum control requirements for Flame Group II Flame Effect include which of the following?
  • What does PME stand for in flame effect safety?
  • Besides the operator, to whom should the operating instructions be made available?
  • How should fuel-soaked waste be stored or disposed of?
  • Who is responsible for the storage, setup, operations, and teardown of all flame effect materials, devices, equipment, systems, and supervision of assistants?
  • Which term describes a container that is factory filled with fuel, not to be refilled, and is equipped with a valve that connects to the appliance receiver?
  • Texas Administrative Code Section 34.8 covers what?
  • What defines a Manual Flame Effect?
  • Only fuels expressly manufactured for burner or combustion applications and specified by the manufacturer of a flame effect appliance shall be used as flame effect fuels for that appliance.
  • How many criteria are required for the emergency stop and complete shutdown of an automatically controlled flame effect?
  • Which of the following is NOT an example of a Flame Group I Type Effect?
  • Which is not a type of Flame Effect Appliance?
  • What is the purpose of evaluating flame effects?
  • Standby fire safety personnel must meet which requirements?
  • What is the purpose of Safety Shutdown (Lockout) in flame effect systems?
  • DoT stands for what?
  • Which flame groups have both unattended and manual fuel controls?
  • What is the purpose of a Man in the Loop in flame effects safety?
  • AHJ stands for which of the following?
  • True or False: Portable accumulators are allowed to be moved to a safe location for discharge.
  • If the ignition means cannot be clearly seen for the entire time, what is required instead of manual arm confirmation?
  • LPG is an acronym for which fuel?
  • Which statement best defines a Use Permit?
  • Are performers and support personnel allowed to be in the flame effect area, and under what condition?
  • Which of the following best defines the Holding Area in flame effect operations?
  • When should the accessible hazard area be under direct observation by the operator or assistant(s) firing the flame effect?
  • Which statement describes a component not listed among the described flame effect valves and controls?
  • What characterizes Portable Flame Effects?
  • What is a 'safety container' as defined in the rules?
  • Manually operated emergency stop control stations must maintain their actuated state until when?
  • All components of the flame effect appliance must be compatible with the fuels and operating pressures specified in the design. True or False?
  • True or False: Personal computers, single-board controllers, and other systems that have control capability but that are not routinely used in protective applications can be used as life safety controllers.
  • For a public display permit, what is the minimum general liability insurance amount required?
  • When should the effect valve open?
  • What does AHJ stand for in flame effect safety?
  • If multiple control power sources are available, which arrangement is described as valid for flame effect control systems?
  • True or False: At least one Texas pyrotechnic special effects operator's licensee must be present on-site at all times where pyrotechnics are used, discharged, or ignited.
  • Cast Members
  • Where should spotters/firewatch be positioned?
  • If fuel is not provided by a central distribution and supplied directly to a flame effect, how much fuel is permitted?
  • What is a Permit?
  • Flame Effect Operator?
  • Which statement is true regarding harm prevention in flame effect control systems?
  • What is required to store quantities in excess of daily usage in holding areas?
  • Where should fueling for a Fire Performer occur?
  • Which term specifically describes a flame effect that is supervised and fired by an automatic control system?
  • Storage Area is defined as
  • What group types are, or can be, manually controlled?
  • Which statement about protection of control system components is true?
  • Which statement describes Flame Group VI Type Effect?
  • In Flame Group II, what ensures shut-off occurs in the event of a failure?
  • Which statement describes Flame Group V Type Effect?
  • If a licensee's license or permit has been revoked, how long must they wait before reapplying?
  • In addition to reapplying after a revocation, what must the licensee request?
  • True or False: Smoking is allowed in areas where fuels used in flame effects are present?
  • What is reaction time?
  • What action should be taken immediately after the flame effect concludes if safety systems were interrupted?
  • When can Fire Props be refueled?
  • What is the minimum age of a Flame Effect Operator?
  • Enable Button is defined as
  • What is the function of the Accumulator Charge Valve?
  • Which statement is NOT a wick requirement?
  • Is LPG lighter or heavier than air?
  • Which approvals are required to interrupt portions of a fire protection and life safety system?
  • Fire refers to
  • Which statement accurately defines Group VII Flame Effect?
  • Liquid Fuel?
  • The document that provides safety information about chemicals used in fueling operations is known as what?
  • Who approves the location for refilling and pressurizing refillable liquid-fuel containers?
  • All flame effect devices and materials shall have drawings, manuals, or written descriptions describing the type of item and performance specifications.
  • Which of the following is NOT an acceptable method for emergency stop and shutdown of a manually controlled flame effect?
  • Which statement best describes the relationship between control power and intentional action for flame effect systems?
  • How far past the anticipated flame contact zone must a shafted prop be made of fire resistant material or be covered?
  • What must a supervisor station be provided the means to do with regards to the shut-off valve?
  • Which device is directly responsive to ignition device attributes necessary for safe operation?
  • Which scenario would be a Flame Group VII Type Effect?
  • Which mechanism can de-energize a control system to permit unattended operation?
  • What are the requirements for valves on an accumulator?
  • Where should control system components be located?
  • Who is responsible for observing the accessible hazard area during the entire time a flame effect is enabled and fired?
  • All Group II through Group VII control systems need what actions to ensure against accidental firing? 1. Deliberately applies control power 2. Enables or arms the system. Which option describes the required mechanism?
  • Does an assistant need to be licensed as a Flame Operator?
  • Fuel Containers and dip buckets must be what when not in use?
  • Which statement correctly describes a Prepackaged Single-Use Container?
  • Which description best matches Group VII Flame Effect?
  • How is Venue defined in the context of flame effects?
  • Which entity has the authority to accept or deny requests related to flame effects or pyrotechnics within a jurisdiction?
  • Hybrid Flame Effect is defined as
  • Liability policy countersignature: who must countersign the liability insurance policy?
  • What does AHJ stand for in fire protection regulation language?
  • The accumulator is defined as
  • Which fuel type is used by a Liquid-Fuel Flame Effect Appliance?
  • MSDS stands for Material Safety Data Sheets.
  • In a flame effects production, which term describes the performers participating in the show that includes flame effects?
  • Accumulator design regulations may come from which organizations for gas pressure safety?
  • Which Flame Groups have visual (manual) flame verification as a feature?
  • For a flame or pyrotechnic effect permit, what is the minimum general liability insurance amount required?
  • Where is the Vent Valve typically located in the fuel train?
  • What additional training should be provided to spotters/firewatch?
  • Where must the additional extinguishers be located for temporary installations?
  • Which term refers to the area made hazardous by the operation of the flame effect?
  • NFPA 1126 and NFPA 160 relate to flame effects. Which statement is true?
  • Why are interlocks required?
  • What is required for overpressure protection in liquid-fuel flame effect systems?
  • Where should the fueling area be located and how should it relate to the audience?
  • What is required when cast members or moving set pieces are present in the hazard area immediately before or after arming and firing?
  • Who has the power to suspend, revoke, or refuse to issue or renew a Flame Operator's license?
  • When are control systems permitted to be unattended?
  • What must be recorded alongside system pressures when testing?
  • NFPA 160 and NFPA 1126 standards are required for audiences of at least how many people?
  • Solid Fuel?
  • Occupation Code Chapter 2154 covers what?
  • Are safety interlocks required to be Fail-Safe?
  • Name an example of an interlock that can be included in flame effect control systems.
  • Which Flame Groups have main show control as a feature?
  • Which term is defined as the source providing oxygen to a combustion reaction?
  • During temperature testing of flame effects, at what rate should the flame be operated to obtain readings?
  • Which of the following is an example of a Flame Group I Type Effect?
  • Which group types must be attended while connected to a fuel source?
  • Under what condition may bare skin be permitted within a flame effect?
  • Who can be permitted to be in the area of a flame effect?
  • Which component is the last fuel shutoff valve before the flame effect burner?
  • Which of the following are acceptable firing methods for flame effects?
  • What is the daily holding area quantity rule for flammable flame effect materials?
  • Which of the following is true regarding automatic control of flame effect groups?
  • For Flame Group I Flame Effect, what are the minimum control requirements?
  • True or False: Where required for operation and maintenance, control systems can have separate sources of control power.
  • Under what condition can fire protection and Life Safety Features be interrupted for permanently installed indoor flame effects?
  • Which description defines Group V Flame Effect?
  • Which controller has responsibility for allowing safety-critical actions in a flame effect control system?
  • For temporary installations, which additional extinguishers are required beyond those normally provided?
  • If a walk-through demonstration is required, how should it be scheduled?
  • What should be provided when cast members can be present immediately before arming and firing the flame effect?
  • If a building uses flame effects and does not have a complete operational fire-sprinkler system, what must be provided to comply?
  • Which item is included in the Flame Effect Plan Content?
  • What is a Primary Safety Control ★?
  • Which item best describes the safety features of a flame effect control system?
  • Fire Watch is best described as
  • Which flame group explicitly requires a fuel supervisory station with fuel pressure limit switches?
  • What defines a Supervisory Control System in flame effects?
  • The volume of the accumulator can exceed what is required to produce the desired flame effect.
  • True or False: Performers and support personnel can be forced to be in the area of a flame effect in the performance of their duties.
  • When should temperatures testing stop?
  • Which Flame Groups have unattended as a feature?
  • True or False: A flame effect does not need to be manually or automatically armed before firing.
  • What must the permit applicant provide with the application regarding insurance?
  • What does the term Safety-Critical mean?
  • If ambient temperature is critical to proper operation, what must manufacturers specify?
  • What procedures should be included in the Operating Procedures of a Flame Effect?
  • Automatic Flame Effect is defined as
  • Which response should occur if the PME enable signal is not sent or is removed during arming and firing?
  • Who coordinates a Fire Hazard Evaluation?
  • Can documentation of the testing and evaluation be prepared by a third party? Under whose approval?
  • Which term refers to materials used as fuel for flame effects and classified by their phase at STP?
  • Which Flame Groups have attended as a feature?
  • Before flame effects or pyrotechnics are used inside a building, what announcement to the assembly must be made?
  • Who determines whether a locked or obstructed exit door constitutes a violation of the occupational code?
  • What temperature should components not exceed?
  • Which statement accurately describes Group VI Flame Effect?
  • Who works under the supervision of the flame effect operator?
  • Can a municipality impose stricter flame effects regulations than these standards?
  • Which on-site personnel is specifically required for pyrotechnic events in Texas?
  • Accessible Hazard Area is defined as
  • Which term best describes the area made hazardous by flame effect operation that is not normally accessible?
  • During pressure testing, what combination of measurements must be recorded with the system pressure?
  • Why are flame effects evaluated?
  • What is required prior to any changes to a performance for a Fire Performer?
  • Which term describes the plan that presents design criteria and assumptions used in the flame effect design?
  • How many spotters are required for each performance and rehearsal with fire?
  • An ignition detection device must not report the presence of an ignition device or pilot due to false sensing of non-fire-related devices.
  • NFPA stands for which organization?
  • Direct Ignition is defined as
  • Who should operate additional PME devices to ensure operators have a clear view of the area?
  • Which statement about the operation of emergency stop stations is true?
  • For leak testing of modular flame piping, which statement is correct?
  • Which statement best describes what enabling comprises in a manually enabled flame effect system?
  • What is the minimum rating for additional extinguishers (not water) accessible to firewatch/spotters for a temporary installation?
  • Fixed-Location accumulators must be designed and installed so that fuel can be safely removed by
  • Which group requires two fuel shutoff valves, one being a safety shut-off valve, in series?
  • What does the use permit expiration address for a temporary flame effect?
  • Which statement is true about hybrid flame effects?
  • Disposal of fuel-soaked waste must be in accordance with which requirements?
  • What type of flame effects can approval be sought in order to interrupt, partially, fire protection and life safety systems?
  • What is the Arm in flame effect control?
  • What action is performed first after the last firing of a flame effect?
  • What do spotters/firewatch need to be familiar with?
  • Which description corresponds to Group IV Flame Effect?
  • Who bears the burden of proving that a license or permit should be granted when reapplying after revocation?
  • Which term describes an area where flame effect material or flame effect devices are stored prior to use or movement to a holding area?
  • How often should flame effects be inspected for normal and safe operating condition and/or retested for operation as designed and anticipated?
  • Can a pre-packaged single-use container be refilled?
  • Which Group Type Effect does not require a control system designed to ensure against accidental firing?
  • Which of the following is NOT listed as NFPA 160 personnel?
  • Testing flame effects: which statement is true?
  • Which step is required before any changes to a fire performance?
  • A use permit specifies which of the following?
  • Which term describes a flame effect that is supervised and fired by an automatic control system?
  • The hazard area surrounding a flame effect must be actively monitored and confirmed clear before firing.
  • In holding areas, which personnel must secure or continuously supervise flammable flame effect materials and loaded devices?
  • Who qualifies as Support Personnel in flame effect operations?
  • Each flame effect shall be provided with an automatic fuel shutoff valve (the effect valve), installed upstream of the burner. Where should this valve be located?
  • Under which condition is a flame effect considered armed via manual confirmation?
  • Which description correctly defines a Prepackaged Single-Use Container Receiver?
  • Flame Group V minimum control requirements include which statements?
  • Which is an example of a monitored condition that could trigger the emergency stop when the limit is exceeded?
  • Flame Effect is defined as
  • Which statement defines Permanent Installation?
  • Fail-Safe means
  • Which of the following actions helps prevent operator complacency during repetitive enabling?
  • Which option best defines the Enable function in a flame control system?
  • Which description best defines a Design Plan for a flame effect?
  • Where must the manual shutoff valve be located for a central fuel distribution system where the point of delivery is outside a building containing the flame effect control system?
  • Direct Ignition
  • In NFPA 160, which valve type is identified as a Safety Shut-off Valve?
  • For temporary installations, how many extinguishers are required in total?
  • What is an approved method for leak-detection during testing?
  • Which feature describes a 'deadman style switch' for PME devices?
  • Which item is a Flame Effect Appliance?
  • Positive confirmation through the use of an interlock or other device of the fuel supply and each auxiliary service is required prior to the continuation of the enable process.
  • What is the minimum rating for water extinguishers accessible to firewatch/spotters for a temporary installation?
  • Prepackaged Single-Use Container Fuel Flame Effect Appliance uses fuel from what?
  • Which statement about testing fire props is correct?
  • How is the Safety Shutoff Valve characterized?
  • Group I Flame Effects are characterized by which control style?
  • Fire props can be refueled after waiting 30 minutes following extinguishment. True or False?
  • How far from the fueling area is the audience prohibited from entering?
  • Which statement about Fire Hazard Evaluations is true?
  • Which statement correctly describes a design consideration for Liquid-Fuel Flame Effect Appliances?
  • Where and with what can reassembled flame effect piping systems that are designed to be separated into subassemblies be leak tested?
  • Which of the following is an example of Flame Group II Type Effect?
  • Which Flame Groups have manual fuel controls as a feature?
  • Which flame groups have both attended and manual flame verification?
  • Where should PME devices be located to ensure operator safety?
  • Separation between the performer and the audience shall be maintained to prevent fuel or flame contact with audience members as approved by the AHJ.
  • Flame Effect Materials are identified by what characteristic at standard conditions?
  • In flame effects operations, the Assistant is
  • What is required regarding the ignition source for liquid-fuel flame effect appliances?
  • Which function is included as a requirement for flame effect control systems?
  • Group I Flame Effect is described as?
  • Ignition detection devices are allowed even if they can produce false-positives due to false sensing of ignition devices, pilots, or flame effects or due to false sensing of other non-fire-related devices normally present in the local environment as long as other fail-safes are provided.
  • Flame Effect Materials are defined as?
  • Which statement best describes a well ventilated fueling area?
  • Are automatic fuel shutoff valves required when control functions are used?
  • Which NFPA standards must be adhered to when using pyrotechnic ignitors with flame effects?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy